Project

General

Profile

Run plan » History » Version 390

Version 389 (Pip Hamilton, 09/08/2017 03:22 PM) → Version 390/1475 (Kevin Wierman, 09/13/2017 02:27 PM)

h1. Run Plan

h2. Contacts

|_. Contact |_. Number |_. Alt Number |
| Shifter | 1 (937) 582-6663 | 1(937) 5-UBOONE |
| Backup Shifter | 1 (978) 822-2582 | 9788 BACK UB |
| RunCo (Kevin) | 425-318-9990 | |
| Deputy RunCo (Pip) | 224-253-2345 | |

[[SLC_-_Guide#Which-expert-to-call-for-which-alarm| Link to which experts to call in case of other alarms]]

h2. Run Configuration

h3. Summary

For *For the time period weekend of 9/13-9/18, all subsystems except for SMC and cryo the 9th to the 10th, the detector is completely OFF. Disregard the instructions below (you will not be offline (invalid). For this time period, please keep an eye on cryo able to take noise runs) and solely monitor for alarms. Our shifters Please pay particular attention to cryo.*

Currently, we
are taking noise data with the only line of defense here and detector with the frequent power outages increase following systems OFF:

* TPC Cathode HV
* Wire Bias
* PMTs
* Purity Monitor
* Laser system

Outside active works periods (i.e. runcos/experts on
the likelihood of failures platform + in the cryo subsystem. control room), shifters should take 5-minute noise runs (*config 633*) once every two hours.

The RunCat is currently down, so you will be unable to do the usual RunCat checks until it is back up. Slow controls and IFIX alarms should still be monitored as per usual.

- Pip.


h3. Run Control

|_. Configuration |_. Config ID |_. Time [min] |
| Zig-Zag Noise Run Configuration | 633 | 5 |
| ASIC config to unmask noise on FT6 | 630 | 5 |
| ASIC config to return FT6 to normal operation | 631 | 5 |

Configs 630 and 631 are misnamed and will be deleted after this period of works is over. They are not to be used for the 5 minute noise runs; only recorded here for posterity when we want to come out of the zig-zag testing configuration.

h2. Notes on current operations:

* MiniBooNE is down until 9/18.
** Do not fill out the miniboone checklist.
* We've been getting dewpoint alarms. The alarm limits are set more conservative than the cryo system's heater control. Therefore this is only a problem if the alarms persist for more than 30 minutes.
* Similarly, the ZMON has been throwing *frequent* alarms. The relevant expert has been informed and investigations are ongoing.
* While Jose is transferring SN data (he'll notify via the gchat), some seb*_memfree alarms may occur intermittently.
* CRT Crate Rails alarms (uB_CrateRails_CRTUtil*) can be ignored until this line is removed from the run plan.
* You may see major OnDetPower HIHI alarms from TPCPS_2_10_904 and 806. These are negative channels whose upper limits are set close to zero - with the wire bias off, small fluctuations in the readback around zero can put them into alarm. Feel free to acknowledge these when you see them; if they reappear it will be due to small fluctuations clearing the alarm state and then putting it back into alarm.

h2. Additional Shifter Requirements:

* Please follow the [[Shift_turnover]] procedures
* At the end of your shift, please post a plot of the last 8 hours of variable: uB_Cryo_IFIX_1_0/PT102
** Minor oscillations below 0.1psig are indicative of the LN2 dewar refilling. This is normal.
** A small spike every 7 hours is expected. Example: http://dbweb6.fnal.gov:8080/ECL/uboone/E/image/47025/Screenshot%20from%202017-08-14%2014-57-26.png
* During access to the detector:
** Please fill out a Beginning of Detector Access and End of Detector Access Form.
** If the "keytree" alarm occurs, and the persons accessing the platform have not called the shifter first, then call LArTF to find out who is accessing the detector. If no one answers, call the runco.
** Detector platform access must be cleared by runcos.
** At the end of detector access, please acknowledge the keybank incomplete alarm.

h2. In Case of Cryo Alarms

All the cryo related alarms from either iFix or slow controls should be documented by shifters in ECL with the alarm variable names.

If a shifter does not receive a call within 15 minutes of seeing a MAJOR cryo alarm:
* Call the Run Coodinator
* If the Run Coordinator cannot be reached
** During Daytime Operating Hours (8am - 10pm CDT)
*** Call the cryo experts in the order listed on the expert call list: http://www-microboone.fnal.gov/at_work/expert_call_list.html
** During nighttime hours:
*** Email the cryo experts