Project

General

Profile

Run plan » History » Version 1422

« Previous - Version 1422/1477 (diff) - Next » - Current version
Zarko Pavlovic, 11/30/2019 08:12 AM


Run Plan - last updated: (check history)

All shifters are required to be very familiar with this page.
Do not hesitate to contact the Run Cos with questions.

Contacts

Contact Number Alt Number
Shifter 1 (937) 582-6663 1(937) 5-UBOONE
Backup Shifter 1 (978) 822-2582 9788 BACK UB
ON-CALL: RunCo (Zarko) (630) 276-9061
OFF-CALL: Deputy RunCo (Ralitsa) (617) 230-2978

Refresh this page Now. Click here: Run plan

Link to which experts to call in case of other alarms

Current Activities

  • We had to change the password for ubooneshift google account. Offsite users using google voice might need to update. The new password is in the usual place.
  • H2O monitor uB_Cryo_IFIX_1_0/AT608 sometimes rises due to outside dewar being filled or due to pressure variations. No need to call, email/slack runco if in alarm.
  • Nominal value for the E:HP875 beam position monitor needs to be updated. Since wrong value is assumed beam projection to the target is incorrectly calculated on the BNB Status page. The variable may also appear in alarm in Slowmon. Experts are aware, no need to call, email or slack anyone.
  • uB_OnDetPower_TPCPS_1_5_404/CURR_READ alarm is acknowledged. Experts are aware.
  • Beam returned end of October. We are back to running Beam on configurations.
  • If you see a uB_DAQStatus_DAQX/sn_read_lag_multiplicity alarm:
  • If you are local and you notice the yellow computer slowing down (cr-02):
    1. Check the "about:performance" tab in the browser. (If the tab is not open, just type "about:performance" in the address line of a new tab). See (and make note of) if any of the web apps are performing poorly.
    2. Close and restart any pages that are performing poorly, or just close and reopen all Firefox windows.
    3. Email or Slack message (don't call) the run coordinator and tell them which app was causing the slow down.

Run Control

Configuration Config ID Time [min]
Physics_EXT16Hz 809 420

Notes on current operations

  • Fill in the usual shift checklist during the shift 2 hours in and 2 hours before end of shift.
  • General procedure: some troubleshooting instructions advocate to stop and restart the run to fix a problem. It is good to do so only once. If stopping and restarting didn't work at the first try, please get in touch with the relevant experts (or the Run Co) and wait for their clearance before stopping and restarting again.
  • Before resetting the PUBS, please ensure there are no PUBS errors being displayed - if there are, please report this to the Data Management expert (via email) before resetting.
  • If you make an elog entry about online monitor or runcat checks failing, upload a screenshot of the plot with the entry.

Additional Shifter Requirements:

  • Please inform the Run Coordinator(s) if
    • you see any DAQ instabilities, or
    • the mean run duration gets smaller than 2h, or
    • you receive any information from MCR about the beam, or
    • there is any mismatch between beam triggers and beam spills (dots and lines of the same color in the nearline trigger monitor).
  • Please do not forget to check your runs in the RunCat.
  • Please fill out the Offline Production Checklist at 9am and 9pm every day.
    There are instruction on how to fill this out on this page: https://cdcvs.fnal.gov/redmine/projects/uboone-operations/wiki/Offline_Production_Checklist_-_Shifters
    • Please note that the offline production checklist has been modified. The content is essentially the same, but if you've done it before, it will look different now. Also, now you email the checklist itself to the offline production listserv rather than composing a separate email.
  • During access to the detector:
    • Make sure the Run Co's were informed of the access (Slack chat or call).
    • Detector platform access must be cleared by Run Co's.
    • Please fill out a Beginning of Detector Access and End of Detector Access Form.
    • If the "keytree" alarm occurs, and the persons accessing the platform have not called or do not call the shifter within ~5 minutes, then call LArTF to find out who is accessing the detector. If no one answers, call the runco.
    • Please remind to the people making the access to call you back when they are done with their work in the pit.
    • At the end of detector access, please acknowledge the keybank incomplete alarm.
  • If you happen to see a pretty event in the event display, take a screenshot!

What should I do if I see alarms during my shift?

Have a look at this wiki page: What to do in case of alarms during a shift

Expert contact information: https://microboone-exp.fnal.gov/at_work/expert_call_list.html