Project

General

Profile

Rack Power ONOFF procedures » History » Version 3

Sowjanya Gollapinni, 08/21/2015 03:13 PM

1 1 Sowjanya Gollapinni
h1. Rack Power ONOFF procedures
2 1 Sowjanya Gollapinni
3 1 Sowjanya Gollapinni
*Step 1:* Make sure the software DAQ/read-out processes are not running. In other words, this means that the platform power off procedure should ONLY be done AFTER the DAQ/computer room racks are powered down. Confirm from the On-call DAQ expert that this is the case before proceeding.
4 1 Sowjanya Gollapinni
5 1 Sowjanya Gollapinni
*Step 2:* Once step 1 is confirmed, go on the platform, with all requirements: Hard hat, closed-toed boots, and most importantly, Two-person rule!
6 1 Sowjanya Gollapinni
7 3 Sowjanya Gollapinni
h2. Readout Electronics Racks Power-Off/On Procedure for Planned Power Outages
8 3 Sowjanya Gollapinni
9 1 Sowjanya Gollapinni
*Important note:* The following racks should be powered off in the following order, and following indicated steps:
10 1 Sowjanya Gollapinni
11 2 Sowjanya Gollapinni
*Side note:* For reference, we are following the reverse of the prescription as written in
12 2 Sowjanya Gollapinni
 http://microboone-docdb.fnal.gov:8080/cgi-bin/RetrieveFile?docid=3825&filename=TPC-R1_Power-up.pdf&version=10 
13 2 Sowjanya Gollapinni
14 2 Sowjanya Gollapinni
15 1 Sowjanya Gollapinni
*1. TPC-R2 through TPC-R5 power off:*
16 1 Sowjanya Gollapinni
a. Switch off both Wiener PS using the red toggle switch on the front panel (push down for 3 seconds).
17 1 Sowjanya Gollapinni
b. Switch off the middle (CB2) and lowest (CB3) circuit breaker by accessing the back side of the rack; verify fans are off.
18 1 Sowjanya Gollapinni
c.  Switch off top (CB1) circuit breaker; verify NetGear network switch inside rack is off.
19 1 Sowjanya Gollapinni
d. Switch off RPS slow controls using front panel switch on the slow controls panel. The +5V, +3.3V, and RPS Status LEDs should turn off.
20 1 Sowjanya Gollapinni
e. Switch off the RPS (use switch behind the RPS unit). Use a step stool to reach, if needed; verify the AC Output ON, POWER, SENSOR, and ALARM LEDs on the AC Switch Box are off.
21 1 Sowjanya Gollapinni
f. Only the AC Input Good LED on the AC Switch Box should be ON.
22 2 Sowjanya Gollapinni
23 2 Sowjanya Gollapinni
*2. TPC-R1 power off:*
24 2 Sowjanya Gollapinni
a. Switch off Wiener PS using the red toggle switch on the front panel (push down for 3 seconds).
25 2 Sowjanya Gollapinni
b. Switch off the lowest (CB3) circuit breaker; verify fans are off.
26 2 Sowjanya Gollapinni
c. Switch off the middle (CB2) circuit breaker; verify NetGear network switch inside rack is off.
27 2 Sowjanya Gollapinni
d. Switch off RPS slow controls using front panel switch on the slow controls panel. The +5V, +3.3V, and RPS Status LEDs should turn off.
28 2 Sowjanya Gollapinni
e. Switch off the RPS (use switch behind the RPS unit). Use a step stool to reach, if needed; verify the AC Output ON, POWER, SENSOR, and ALARM LEDs on the AC Switch Box are off.
29 2 Sowjanya Gollapinni
f. Only the AC Input Good LED on the AC Switch Box should be ON.
30 2 Sowjanya Gollapinni
31 2 Sowjanya Gollapinni
*3. LIZ Rack power off:*
32 2 Sowjanya Gollapinni
a. Switch off the two NIM bins using their front panel switches.
33 2 Sowjanya Gollapinni
b. Switch off the function generator (Strobe pulser) using its front panel on/off button.
34 2 Sowjanya Gollapinni
c. Switch off the fan switch on the fan front panel; verify the fan is off.
35 2 Sowjanya Gollapinni
d. Switch off the middle (CB2), top (CB1), and bottom (CB3) circuit breakers. 
36 2 Sowjanya Gollapinni
e. Switch off RPS slow controls using front panel switch on the slow controls panel. The +5V, +3.3V, and RPS Status LEDs should turn off.
37 2 Sowjanya Gollapinni
f. Switch off the RPS (use switch behind the RPS unit). Use a step stool to reach, if needed; verify the AC Output ON, POWER, SENSOR, and ALARM LEDs on the AC Switch Box are off.
38 2 Sowjanya Gollapinni
g. Only the AC Input Good LED on the AC Switch Box should be ON.
39 2 Sowjanya Gollapinni
40 2 Sowjanya Gollapinni
*4. PMT/TRIG Rack power off:*
41 2 Sowjanya Gollapinni
a. Switch off Wiener PS using the red toggle switch on the front panel (push down for 3 seconds).
42 2 Sowjanya Gollapinni
b. Switch off the NIM bin using its front panel switch.
43 2 Sowjanya Gollapinni
c. Check that the PMT HV (CB3) bottom circuit breaker is off. If not, stop and call a PMT HV expert. 
44 2 Sowjanya Gollapinni
d. Switch off the middle (CB2) circuit breaker; verify the fan is off.
45 2 Sowjanya Gollapinni
e. Switch off the CB1 circuit breaker; verify NetGear network switch inside rack is off.
46 2 Sowjanya Gollapinni
f. Switch off RPS slow controls using front panel switch on the slow controls panel. The +5V, +3.3V, and RPS Status LEDs should turn off.
47 2 Sowjanya Gollapinni
g. Switch off the RPS (use switch behind the RPS unit). Use a step stool to reach, if needed; verify the AC Output ON, POWER, SENSOR, and ALARM LEDs on the AC Switch Box are off.
48 2 Sowjanya Gollapinni
h. Only the AC Input Good LED on the AC Switch Box should be ON.
49 2 Sowjanya Gollapinni
50 2 Sowjanya Gollapinni
5. Make an elog entry that the readout electronics racks have been successfully powered off.