Project

General

Profile

List of config files and their purposes

Config files that be used for current running are listed here (before the full list of config files), and shown in bold in the full list. Please keep both lists up to date!


Config files for current running:

The "golden config" for current running conditions is:

  • 809 - PHYSICS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
  • Config file identical to config 803 with updated zero suppression parameters March 2019

Other acceptable configs are:

  • 810 - PHYSICS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
  • Config file identical to config 809 with 7 Hz ext rate
  • 811 - PHYSICS_EXT990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
  • Config file identical to config 809 with 1 Hz ext rate

Full list of all config files:

  • 476 - PMT_noTPC_c11_10Hz-run-16698.fcl
    • no TPC PMT only config used to monitor PMTs when slow mon / cryo was down.
  • 681 - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2Stream_LowThreshold50_c2
    • 7Hz EXT trigger rate, and extra software triggers for low threshold (5.0 PE) on BNB and BNB_EXT.
  • 682 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2Stream_LowThreshold_BNB50_NuMI90_c0
    • Same as 681, but added low-threshold software triggers for NuMI and HSN.
  • 683 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2Stream_LowThreshold_BNB50_NuMI85_c0
    • Same as 681, but added low-threshold software triggers for NuMI and HSN (with different threshold values).
  • 684 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2Stream_LowThreshold_BNB50_NuMI80_c0
    • Same as 681, but added low-threshold software triggers for NuMI and HSN (with different threshold values).
  • 685 - PHYSICS_BNB_NUMI_MUCS_EXT990mHz_SWTrigger_2Stream_LowThreshold50_c0
    • Same as 681, but with EXT rate at 1 Hz
  • 686 - PHYSICS_BNB_NUMI_MUCS_EXT3990mHz_SWTrigger_2Stream_LowThreshold50_c0
    • Same as 681, but with EXT rate at 4 Hz
  • 687 - PHYSICS_BNB_NUMI_MUCS_EXT9990mHz_SWTrigger_2Stream_LowThreshold50_c0
    • Same as 681, but with EXT rate at 10 Hz
  • 688 - PHYSICS_BNB_NUMI_MUCS_EXT11990mHz_SWTrigger_2Stream_LowThreshold50_c0
    • Same as 681, but with EXT rate at 12 Hz
  • 689 (expert) - BeamOff_EXT1Hz_2Stream_c0
    • Special config made for taking beam-off data (at the request of M. Mooney, who was interested in taking low-rate EXT data while the HV was being ramped down and back up again during maintenance). Not to be used during normal running.
  • [ARCHIVED] 690
    • Move OM to run on near2 (because near1 is out for repairs). This config had a bug so was immediately retired.
  • 691 - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2Stream_LowThreshold50_c4
    • Fix error in config 690. Still has OM running on near2
  • 692 - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2Stream_LowThreshold50_c0
    • Same as 681, but with EXT rate at 16 Hz
  • 693 - PHYSICS_BNB_NUMI_EXT990mHz_SWTrigger_2Stream_LowThreshold50_c0
    • Has EXT rate at 1 Hz and trigmask8: 0x32 (compared to 0x132 for normal running). This masks out MuCS, and was a special configuration made when MuCS was causing problems after an unexpected power outage. Not to be used in normal running.
  • 694 (expert) - PHYSICS_BNB_NUMI_EXT990mHz_SWTrigger_2Stream_UnbiasedAll_c0
    • (From Kirsty) I'm not sure what this one is - it also has trigmask8: 0x32 so no MuCS, so I guess it's from the same day as 693. Either way, don't use in normal running.
  • 695 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT11990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueues.fcl
    • First config file with configurable queue lengths. Added new parameters assemblerAppevb.fragment_reception.assembler_max_art_queue_size (default 300 if not included in config file) and sebAppsebXX.nu_stream.max_fragment_queue_size, sebAppsebXX.sn_stream.max_fragment_queue_size, and sebAppseb10.trg_stream.max_fragment_queue_size (all set to 200 by default if not included in config file). In this file, the values are as below:
    • assembler_max_art_queue_size = 300
    • max_fragment_queue_size (all instances) = 200
    • Otherwise identical to config 688
  • 696 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT11990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueues1.fcl
    • Config for testing configurable queue lengths with different values. Values as shown below, otherwise identical to config 688.
    • assembler_max_art_queue_size = 600
    • max_fragment_queue_size (all instances) = 400
  • 697 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT11990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueues2.fcl
    • Config for testing configurable queue lengths with different values. Values as shown below, otherwise identical to config 688.
    • assembler_max_art_queue_size = 1000
    • max_fragment_queue_size (all instances) = 400
  • 698 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueues1.fcl
    • Identical to config 696, but with EXT rate at 16 Hz.
  • 699 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT19990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB1000SEB800
    • Identical to config 696, except with the following:
    • 20 Hz EXT
    • assembler_max_art_queue_size = 1000
    • max_fragment_queue_size (all instances) = 800
  • 700 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB1500SEB1000
    • Identical to config 696, except with the following:
    • 25 Hz EXT
    • assembler_max_art_queue_size = 1500
    • max_fragment_queue_size (all instances) = 1000
  • 701 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB2000SEB1500
    • Identical to config 696, except with the following:
    • 25 Hz EXT
    • assembler_max_art_queue_size = 2000
    • max_fragment_queue_size (all instances) = 1500
  • 702 (expert) -
    PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB3000SEB2000_circular2G
    • Identical to config 696, except with the following:
    • 25 Hz EXT
    • assembler_max_art_queue_size = 3000
    • max_fragment_queue_size (NU stream only) = 2000
    • max_fragment_queue_size (TRG stream only) = 200
    • Change max_fragment_queue_size for the SN stream and trigger stream back to default (200).
    • nu_stream.circular_buffer_size = 2e9 (instead of 1e9 in previous fcls)
  • 703 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB2000_circularbuffer2G
    • Identical to config 696, except with the following:
    • 25 Hz EXT
    • assembler_max_art_queue_size = 3000
    • max_fragment_queue_size (all instances except trigger stream) = 2000
    • max_fragment_queue_size = 200 for trigger stream only
    • nu_stream.circular_buffer_size = 2e9 (instead of 1e9 in previous fcls)
  • 704 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB3000SEBNUSNstream2000TRG1000_circularbuffer2G
    • Identical to config 703, except with the following:
    • max_fragment_queue_size = 1000 for trigger stream only
  • 705 - PHYSICS_BNB_NUMI_MUCS_EXT19990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB2000_circularbuffer2G
    • Identical to config 703, but with 20 Hz EXT rate
  • 706 - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB2000_circularbuffer2G
    • Identical to config 703, but with 16 Hz EXT rate
  • [ARCHIVED] 707 (expert) - Test_pmt6thresh1_200_EXT24990mHz_c0
    • Identical to config 703, but with pmt6.threshold1 = 200 (i.e. cosmic discriminator for high-gain PMT signals at 10 PE). Not to be used for normal physics running!
  • [ARCHIVED] 708 (expert) - Test_pmt6thresh1_130_EXT0990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 130 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 709 (expert) - BeamOff_pmt6thresh1_120_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 120 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 710 (expert) - BeamOff_pmt6thresh1_110_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 110 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 711 (expert) - BeamOff_pmt6thresh1_100_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 100 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 712 (expert) - BeamOff_pmt6thresh1_90_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 90 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 713 (expert) - BeamOff_pmt6thresh1_80_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 80 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 714 (expert) - BeamOff_pmt6thresh1_70_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 70 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 715 (expert) - BeamOff_pmt6thresh1_60_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 60 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 716 (expert) - BeamOff_pmt6thresh1_50_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 50 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 717 (expert) - BeamOff_pmt6thresh1_40_EXT9990mHz_c0.fcl
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 40 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 718 (expert) - Test_pmt6thresh1_130_EXT9980mHz_c0.fcl
    • Almost identical to config 687 (10 Hz EXT rate, but this is 9.98 instead of 9.99 Hz) but with pmt6.threshold1 = 130 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 719 (expert) - BeamOff_pmt6thresh1_30_EXT9990mHz_c0
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 30 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 720 (expert) - BeamOff_pmt6thresh1_20_EXT9990mHz_c0
    • Identical to config 687 (10 Hz EXT rate) but with pmt6.threshold1 = 20 (instead of 140 as normal). Used for testing during downtime, not to be used for normal physics running!
  • 721 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB3000SEB2000SEB10NUSNstream1500TRG500_circularbuffer2G
    • Identical to config 703, except with max_fragment_queue_size = 1500 for SN stream on SEB 10 and 500 for trigger stream on SEB 10 (2000 for NU and SN stream on all other SEBs)
  • 722 - PHYSICS_BNB_NUMI_MUCS_EXT11990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB2000_circularbuffer2G
    • Identical to config 703, but with 12 Hz EXT rate
  • 723 (expert) - Test_EXT24990mHz_pmt6thresh1_240
    • Identical to config 703, but with pmt6.threshold1 = 240 (i.e. cosmic discriminator for high-gain PMT signals at 12 PE). Also uploaded as "Test", and writes data into /data/uboonedaq/TestRuns, so data is not swizzled. Not to be used for normal physics running!
  • 724 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB3000SEB2000TRG50_circular2G
    • Identical to config 703, except with max_fragment_queue_size = 50 for trigger stream on SEB 10 (2000 for NU and SN stream on SEB 10 and all other SEBs)
  • 725 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB3000SEB2000SEB10_100_circular2G
    • Identical to config 703, except with max_fragment_queue_size = 100 for trigger, NU, and SN stream on SEB 10 (2000 for NU and SN stream on all other SEBs)
  • 726 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB3000SEB2000SEB10_500TRG200_circular2G
    • Identical to config 703, except with max_fragment_queue_size = 100 for trigger stream on SEB 10, and 500 for the NU, and SN streams on SEB 10 (2000 for NU and SN stream on all other SEBs)
  • 727 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesEVB3000SEB500TRG200_circular2G
    • Identical to config 703, except with max_fragment_queue_size = 500 for all streams on all SEBs, except for the trigger stream on SEB 10, which is equal to 200.
  • 728 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G
    • Identical to config 706 (16 Hz EXT rate), except with max_fragment_queue_size = 500 for all streams on all SEBs, except for the trigger stream on SEB 10, which is equal to 200
  • [ARCHIVED] 729 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c1
    • Identical to config 728, but with an addition of the following lines in sebAppseb06 only:
      sebAppseb06:{
         ...
         fragment_recycler:{
            max_fragment_count: 200
         }
         ...
      }
      
    • These lines should set the max_fragment_count for the recycler to 200, meaning that it will not store more than 200 empty fragments in case they are needed (the default value is 500). This config was archived because we decided to move to config 730 and test it out on all sebs at the same time.
  • [ARCHIVED] 730 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c2
    • Identical to config 728, but with the lines sebAppsebXX.fragment_recycler.max_fragment_count: 200 inserted for all SEBs.
    • Had no effect on the recycler max fragment count, so it seems that we put this at the wrong scope and it wasn't read in by the right bit of the DAQ code. Archived for this reason.
  • 731 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c3
    • Identical to config 728, but with the lines sebAppsebXX.nustream.fragment_recycler.max_fragment_count: 200 inserted for all SEBs.
    • Similar to config 730, but try putting recycler section inside nu_stream (maybe that's the right scope?)
  • 732 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c4
    • Identical to config 728, but with the lines fragment_recycler.max_fragment_count: 200 in its own block (not inside any sebApp/assembler/dispatcher block). Finally, this seems to be the right scope.
  • 733 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G
    • Identical to config 728, but with the EXT rate set to 7Hz.
  • 734 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT990mHz_SWTrigger_2Stream_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G
    • Identical to config 728, but with the EXT rate set to 1Hz.
  • 735 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G
    • Identical to config 728 (i.e. 16 Hz EXT, same queue lengths), but includes two new software trigger configs for the NuMI stream:
      • EXT_NUMIwin_2018May_FEMBeamTriggerAlgo
      • NUMI_2018May_FEMBeamTriggerAlgo
    • These two extra software triggers have TriggerThresPHMAX: 115 (instead of 190 in the normal NuMI software trigger). That essentially gives a threshold of 5.75 PE instead of 9.5 PE, to restore the NuMI pass-rate to 14% as based on DocDB 15758. The new trigger stream will run in parallel with the existing NuMI trigger stream, as is done for the BNB, so we can always separate events that pass the "old" trigger if we want to.
  • 736 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G
    • Identical to 735 but with EXT at 7 Hz
  • 737 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G
    • Identical to config 735 but with EXT at 1 Hz
  • 738 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_EXTPrescale1
    • Identical to config 735, but with the prescaleFactor for the software trigger algorithm EXT_unbiased_PreScaleAlgo set to 1.0 (usually it is 0.02). No other changes to the config file. This was produced for some tests in which we want to save all EXT data, and should not be used during normal running.
  • 740 (expert) - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G
    • Same as 735 but with 25Hz EXT.
  • 742 - PHYSICS_BNB_NUMI_MUCS_EXT990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c2
    • 2 software trigger streams for NuMI and BNB, adjusted BNB RWM alarm thresholds after fiber swap, 1Hz EXT
  • 743 - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c2
    • 2 software trigger streams for NuMI and BNB, adjusted BNB RWM alarm thresholds after fiber swap, 7Hz EXT
  • 744 - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c2
    • 2 software trigger streams for NuMI and BNB, adjusted BNB RWM alarm thresholds after fiber swap, 16Hz EXT
  • 745 - PHYSICS_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c2
    • 2 software trigger streams for NuMI and BNB, adjusted BNB RWM alarm thresholds after fiber swap, 25Hz EXT
  • 746 (expert) - Test_EXT29990mHz_pmt5deadtime_2047_pmt6deadtime_2047
    • test config w/ increased deadtime (2047 ticks) in the LG and HG cosmic discriminators (pmt5 and pmt6). EXT rate 30 Hz.
  • 747 (expert) - Test_EXT24990mHz_pmt5deadtime_2047_pmt6deadtime_2047
    • test config w/ increased deadtime (2047 ticks) in the LG and HG cosmic discriminators (pmt5 and pmt6). EXT rate 25 Hz.
  • 748 (expert) - Test_EXT24990mHz_pmt5deadtime_2000_pmt6deadtime_2000
    • test config w/ increased deadtime (2000 ticks) in the LG and HG cosmic discriminators (pmt5 and pmt6). EXT rate 25 Hz.
  • 749 - PHYSICS_BNB_NUMI_MUCS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c3
    • 2 software trigger streams for NuMI and BNB, adjusted BNB/NuMI RWM alarm thresholds after fiber swap, 16Hz EXT
  • 750 (expert) - Test_BNB_NUMI_MUCS_EXT24990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c3
    • 2 software trigger streams for NuMI and BNB, adjusted BNB/NuMI RWM alarm thresholds after fiber swap, 25Hz EXT
  • 751 - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c3
    • 2 software trigger streams for NuMI and BNB, adjusted BNB/NuMI RWM alarm thresholds after fiber swap, 7Hz EXT
  • 752 - PHYSICS_BNB_NUMI_MUCS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c4
    • Identical to config 751, but with updated NuMI RWM alarm limits in the online monitor. Limits are now set at 857 and 865, instead of 842 and 850 as in the old config files. These limits should be kept, so all new configs should be based on this one!
  • 753 - BeamOff_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c0
    • Config file for summer shutdown. Identical to config 752, but uploaded with config type "BeamOff" and "BeamOff" file type for data management. 7 Hz EXT rate.
  • 754 - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c0
    • Config file for summer shutdown. Identical to config 752, but with 16 Hz EXT rate. Uploaded with config type "BeamOff" and "BeamOff" file type for data management.
  • 755 - BeamOff_EXT11990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c0
    • Config file for summer shutdown. Identical to config 752, but with 12 Hz EXT rate. Uploaded with config type "BeamOff" and "BeamOff" file type for data management.
  • 756 - BeamOff_EXT4990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_configurableQueuesNUSNstreamEVB3000SEB500TRG200_circularbuffer2G_c0
    • Config file for summer shutdown. Identical to config 752, but with 5 Hz EXT rate. Uploaded with config type "BeamOff" and "BeamOff" file type for data management.
  • [ARCHIVED] 757 - Archived
  • 758 (expert) - LaserTriggerOnly_NoLaserFrag_NoPMTFrag_OptimisedQueues
    • Config file for laser runs in July 2018. Not to be used for normal running.
  • 759 (expert) - LaserTriggerOnly_NoLaserFrag_NoPMTFrag_OptimisedQueues_500mHz
    • Config file for laser runs in July 2018. Not to be used for normal running.
  • 760 - BeamOff_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c0
    • Config file for summer shutdown. Identical to config 752, but with updated zero suppression parameters from read out team . Uploaded with config type "BeamOff" and "BeamOff" file type for data management.
  • 761 - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c0
    • Config file for summer shutdown. Identical to config 760, but with 16 Hz EXT rate. Uploaded with config type "BeamOff" and "BeamOff" file type for data management.
  • 762 - BeamOff_EXT11990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c0
    • Config file for summer shutdown. Identical to config 760, but with 12 Hz EXT rate. Uploaded with config type "BeamOff" and "BeamOff" file type for data management.
  • 763 - BeamOff_EXT4990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c0
    • Config file for summer shutdown. Identical to config 760, but with 5 Hz EXT rate. Uploaded with config type "BeamOff" and "BeamOff" file type for data management.
  • 764 (expert) - BeamOff_EXT4990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_EXTubprescale1_c0
    • Config file for tests of whether the DAQ can cope with an EXT unbiased prescale factor of 1. Identical to config 763, except: EXT_unbiased_PrescaleAlgo.PrescaleFactor = 1.0 and EXT rate of 5 Hz.
  • 765 (expert) - BeamOff_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_EXTubprescale1_c0
    • Config file for tests of whether the DAQ can cope with an EXT unbiased prescale factor of 1. Identical to config 763, except: EXT_unbiased_PrescaleAlgo.PrescaleFactor = 1.0 and EXT rate of 7 Hz.
  • 766 (expert) - BeamOff_EXT9990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_EXTubprescale1_c0
    • Config file for tests of whether the DAQ can cope with an EXT unbiased prescale factor of 1. Identical to config 763, except: EXT_unbiased_PrescaleAlgo.PrescaleFactor = 1.0 and EXT rate of 10 Hz.
  • 767 (expert) - BeamOff_EXT11990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_EXTubprescale1_c0
    • Config file for tests of whether the DAQ can cope with an EXT unbiased prescale factor of 1. Identical to config 763, except: EXT_unbiased_PrescaleAlgo.PrescaleFactor = 1.0 and EXT rate of 12 Hz.
  • 780 (expert) - LaserTriggerOnly_NoLaserFrag_NoPMTFrag_OptimisedQueues_c1
    • Config for laser calibration runs with parameters for new seb01 (but old seb02-10).
  • 781 and other missing configs between 767 and 780
    • Testing different bus numbers during SEB replacement. Do not use these configs for normal running!
  • 782 - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c10_newSEBs
    • 16 Hz EXT. Updated bus numbers for all new SEBs (seb01 to seb10):
    • For seb01-seb09:
      • neviscard_controller.bus : 0x66
      • neviscard_nu.bus : 0xb4
      • neviscard_sn.bus : 0xb3
    • For seb10:
      • neviscard_controller.bus : 0x67
      • neviscard_nu.bus : 0xb4
      • neviscard_sn.bus : 0xb3
      • (note: the gps card is in slot 0x66, but that is not set in the config file)
  • [ARCHIVED] 783 (expert) - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c10_newSEBs_noPMTs
    • Previous run failed, we think because the PMTs are off so we have no PMT fragments. Made a new config identical to 782 but with only 2 FEMs for SEB 10, so it doesn't expect PMT data. Archived because we put this in as a "BeamOff" config, which means the data will get processed as normal and treated as good data (but obviously we don't want that because there are no PMTs so it's not good quality data).
  • 784 (expert) - Test_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c10_newSEBs_noPMTs
    • Identical to config 783, but changed run type to "Test" and output directory to "TestRuns". Phew!
  • 785 (expert) - Test_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c10_newSEBs_noPMTs_noseb9
    • Seb09 is being annoying so we're masking it out (to see if we can take data and then we'll deal with it later). Obviously don't use this for normal running.
  • 786 (expert) - LaserTriggerOnly_NoLaserFrag_NoPMTFrag_OptimisedQueues_c2
    • Config file for laser runs with updated SEB bus numbers (see elog 78473)
  • 787 (expert) - LaserTriggerOnly_NoLaserFrag_NoPMTFrag_OptimisedQueues_noseb3_c2
    • Config file for laser runs with updated SEB bus numbers, with SEB03 masked out (see elog 78485)
  • 789 (expert) - LaserTriggerOnly_NoLaserFrag_NoPMTFrag_OptimisedQueues_noseb5_c2
    • Config file for laser runs with updated SEB bus numbers, with SEB05 masked out (see elog 78536)
  • 790 (expert) - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_c10_newSEBs_ConfigASIC
    • Config file for reconfiguring ASICs after power outages, with updated SEB bus numbers.
  • 791 (expert) - Test_EXT9990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_noPMTs_EXTubprescale1
    • Config file with an EXT unbiased prescale factor of 1. Identical to config 784, except: EXT_unbiased_PrescaleAlgo.PrescaleFactor = 1.0 and EXT rate of 10 Hz.
  • 792 (expert) - PMT_noTPC_c11_10Hz_1808seb10
    • same as 476, for PMT calibration, no TPC PMT only config used to monitor PMTs when slow mon / cryo was down, only for the new SEB10
  • 793 (expert) - LaserTriggerOnly_NoLaserFrag_NoPMTFrag_OptimisedQueues_SN_c0
    • New config for laser runs with updated bus numbers. Same as config 786, but also runs the SN stream (as well as NU stream).
  • 794 - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_c11_newSEBs
    • Identical to config 782 (16Hz EXT, updated SEB bus numbers), but updated zero suppression parameters for SN stream following ASIC reconfiguration on August 27th.
  • 795 (expert) - BeamOff_EXT9990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_EXTubPrescale1
    • Config file with an EXT unbiased prescale factor of 1. Identical to config 794, except: EXT_unbiased_PrescaleAlgo.PrescaleFactor = 1.0 and EXT rate of 10 Hz.
  • 796 - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_queuesTestEVB300SEB2000_newSEBs
    • Config file Identical to config 794, with different queues for the SEBs (2000 instead of 500) to test efficiency
  • 797 (expert) - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_queuesTestEVB300SEB1000_newSEBs
    • Config file Identical to config 794, with different queues for the SEBs (1000 instead of 500) to test efficiency
  • 798 - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_queuesTestEVB300SEB2000_newSEBs_newbl
    • Config file Identical to config 796 but with new bl to complement the new DAQ release and enable static baselines
  • 799 - PHYSICS_EXT990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 794 but with new bl to complement the new DAQ release and enable static baselines and for physics run and 1 Hz EXT trigger
  • 800 - PHYSICS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 799 but with 7 Hz EXT trigger
  • 801 - PHYSICS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 799 but with 16 Hz EXT trigger
  • 802 - archived
  • 803 - PHYSICS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_newbl_c1
    • Identical to config 801 but with BNB_unbiased.PrescaleFactor = 0.1 instead of 0.0026. The plan is to use this config file only for a couple of days, to check the beam-on vs beam-off software trigger firing rates with higher statistics. As far as I know, we do not intend to run with this config long-term (config 801 should be used instead).
  • 804 - PHYSICS_EXT990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 799 but with OM alarm levels on the BNB RWM timing shifted by +2 ticks
  • 805 - PHYSICS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 804 but with 7 Hz EXT trigger
  • 806 - PHYSICS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1808OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 804 but with 16 Hz EXT trigger
  • 808 - PMT_noTPC_c12_10Hz
    • same as 476 with the new seb10 card numbers
  • 809 - PHYSICS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 803 with updated zero suppression parameters March 2019
  • 810 - PHYSICS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 809 with 7 Hz ext rate
  • 811 - PHYSICS_EXT990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 809 with 1 Hz ext rate
  • 813 - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 809 for BeamOff
  • 814 - BeamOff_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 813 with 7 Hz ext rate
  • 815 - BeamOff_EXT990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Config file identical to config 813 with 1 Hz ext rate
  • 816 (expert) - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl_DoASICReconfig
    • Config file identical to config 813 (16 Hz ext rate) except it does ASIC configuration at the start of the run.
  • 817 (expert)
    • Unknown. Do not use in normal circumstances!
  • 818 (expert) - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl_DoASICReconfig_FT10P0_FT6P1
    • ASIC configuration of FT10P0 and FT6P1. Do not use in normal circumstances!
  • 819 (expert) - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl_DoASICReconfig_FT10P0
    • ASIC configuration of FT10P0. Do not use in normal circumstances!
  • 820 (expert) - N/A
    • burnt. Do not use in normal circumstances!
  • 821 (expert) - BeamOff_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl_DoASICReconfig_FT10
    • ASIC configuration of FT10. Do not use in normal circumstances!
  • 822 (expert) - PHYSICS_EXT0mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Identical to config 809 but has EXT rate (Strobe1.frequency) set to 0. This was for specific tests requested by the RunCos to investigate how EXT data taking affects the NuMI rate. Do not use in normal circumstances!
  • 823 (expert) - PHYSICS_EXT0001mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl
    • Identical to config 809 but has EXT rate (Strobe1.frequency) set to 0.01. This was for specific tests requested by the RunCos to investigate how EXT data taking affects the NuMI rate. Do not use in normal circumstances!
  • 824 - @PHYSICS_EXT990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl_NUMItiming2002
    • Identical to config 811 with updated NUMI window time as off February 14th 2020
  • 825- @PHYSICS_EXT6990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl_NUMItiming2002
    • Identical to config 824 with 7 Hz ext rate
  • 826 - @PHYSICS_EXT15990mHz_SWTrigger_2StreamBNBandNuMI_LowThreshold50_1903OptimisedQueuesZeroSupPars_newSEBs_newbl_NUMItiming2002
    • Identical to config 824 with 16 Hz ext rate