Project

General

Profile

Conventions and Tools » History » Version 33

« Previous - Version 33/48 (diff) - Next » - Current version
Teresa Lackey, 09/09/2016 12:35 PM


Conventions and Tools

Overview

The user interface environment to the DAQ system is hosted in VNC servers running on DAQ cluster computers at various sites. Users interact with these via VNC viewers hosted on control room desktops, and for experts, on their own desktop or laptop.

The NovaControlRoom package contains icons and scripts to automatically set up the needed ssh tunnels, and launch the VNC viewers. See docdb-8406 for a User's Guide.

VNC Servers

To set up VNC servers for the control room, see the VNC Setup How-To.

VNC Viewers

The command to start a viewer is including in the script launched by the desktop icons described in the User's Manual mentioned above, but the underlying command is of the form

 vncviewer -Fullscreen -Shared -passwd ~/.vnc/passwd :<NN> 

where
 -Fullscreen # starts in full screen mode
 -Shared # keeps other users from getting disconnected from the server when you connect
 NN # two-digit port number (relative to 5900) 

Conventions

VNC Servers

In the current model (as of 2016-05-10), we employ 2 VNC servers for each detector. In order to allow for different desktop environments on a single host machine, each VNC server on is run under a different account, using a dedicated port. We tend to use certain servers for particular functions, but this is subject to change.

The table below gives the VNC server host name used for each system:

Abbreviation Host Used in standard ROC?
NDOS novadaq-ctrl-master No
NDSBTest novadaq-ctrl-master No
FarDet novadaq-far-master-02 Yes
NearDet novadaq-near-master Yes
NearGateway novadaq-near-gateway-01 Yes

(See novadaq_apdtest for more information on NDSBTest)

The next table gives machine, account, and port information for each of the six stations used at a Remote Operation Center (ROC):

Station Functions Host Account Gateway Remote Port Gateway Port Local Port
1 FD Run Control
Message Logger
novadaq-far-master-02 novacr01 novadaq-far-gateway-01 5951 5903 5981
2 FD Event Display
Online Monitoring
APD Cooling GUI
novadaq-far-master-02 novacr02 novadaq-far-gateway-01 5952 5900 5982
3 Synoptics nova-cr-03 novacr03 novadaq-near-gateway-01 5953 5902 5993
4 Camera pages
beam pages
webpage
5 ND Run Control
Message Logger
novadaq-near-master novacr01 novadaq-near-gateway-01 5951 5900 5991
6 ND Event Display
Online Monitoring
APD Cooling GUI
novadaq-near-master novacr02 novadaq-near-gateway-01 5952 5901 5992

The gateway and gateway port are what you need to know to set up your own SSH tunnels so that you can view the sessions from your local machine. The local port is a recommendation for what port to use on your local machine.

The servers for each of these is set up to occupy a 1x2 monitor grid, with total pixel count 2650x2880.

Two VNC servers run on the nova-daq-04 Control Room desktop in the Fermilab 1st floor control room, hosting webcam displays. From off-site, webcam and beam pages can be found on the What to do on Shift links site.

VNC has a port base of 5900. However, in addition to the VNC connection itself, it also uses a port for the X11 connection 100 higher than the VNC port. Since general X11 connections use ports starting at 6010, and assuming less than 40 open connections is a safe bet, a good assumption for VNC port ranges that avoid conflicts with X11 would be 5900-5909 and 5950-5999.

ssh Tunnels

ssh tunnels are required to access the port for a VNC server on a remote host (e.g., for station 1 on NDOS) from a localhost (e.g., your laptop, or a control room desktop). Once launched, the tunnel can remain active indefinitely. The ssh command has the form

ssh -L <local_port>:localhost:<remote_port> -N -f -l <remote account> <remote host> 

The ssh tunnel is authenticated using a kerberos ticket on the localhost, usually for a special use (i.e., non-personal) principle. That principle must be in the k5login file for the remote account, and the remote host must be directly reachable from the localhost (i.e., the localhost must be in the fnal.gov domain.)

Since a single desktop will often have connections to the "same" display on multiple detectors, we need to have localhost port assignments vary by detector. The scheme in use by the NovaControlRoom package is

Example

EXPERTS ONLY
On Windows, using RealVNC Viewer (renamed to vncviewer.exe), MIT Kerberos for Windows, and plink; the following batch file (FarDet1.bat) connects to the first screen of the Far Detector:
Start plink -ssh -L 5981:localhost:5981 <Principal>@<Gateway> "ssh -L 5981:localhost:5951 -N "
pause
start vncviewer -Shared -passwd passwd localhost:81

passwd is a file with the MD5'd VNC viewer password, and <Gateway> is a machine connected to the Fermilab network accessible from the outside. Using the tables above, it is possible to connect to any detector/station combination.